Featured Products
Featured

sold out
HELPeR GLOCK
$95.00


Modular Optic Shroud
A20X Aluminum + Hard coat anodizing
Direct replacement of the factory shroud
MLOK slots on top, left and right
Textured thumb pads
Compatible with 1913 Picatinny rail segments or a line of optic plates that will accompany the release.
MLOK Thumb Rest in PA12 Nylon
Pictured is a PLA prototype
Final pricing and eta is still being decided, but not far off. Planning to also offer as a bundle with HELPeR charging handles.

The current state of HELPeRs
Most are available for ordering now, the RXM and Glock models will go live in the future when those Raiders get closer and I can test them.
This next batch closes in less than 72 hours with an ETA of late April, they’re usually done in a matter of days, but the rest is up to the anodizers, then I pack and ship them all the same day I get them back.
This should cover the most common footprints, but if something is missing let me know below. Working on a few other things I hope to show off soon.

Alright, prototype day photo and info dump time.
Ruger RXM, everybody knows by now that the RXM Raider is coming eventually. So to be ready and get ahead of things, I drew up Tall and Tall portal versions of the HELPeR, and decided to match the serrations of the factory slide. Let me know what you think on which to offer in the poll, serrated v plain?
Secondary to the RXM, it uses Deltapoint Pro footprint and mounting lugs, this should verify I have sufficient clearance for the recoil lugs for further DPP models like 3rd party 320 slides cut for DPP, I’ll offer them but still strongly suggest OEM slides.
ZEV P320, this required a different approach to clear the optic hood on the Raider. I offset the paddle section forward leaving plenty of clearance for both Tall/Tall Portal and Short/Short V models. As the video shows, the Short models are still fully compatible with the Halo. These SHOULD fit other 320 slides cut for RMR with or without Zev posts and 82° Torx screws, but depth and location of the cut may or may not be a factor when it comes to the Raiders optic mount, guys that chop will have no problem. One thing to note, if you have an “irons forward” cut slide, these will not be compatible, it places the optic cut too far rearward to clear the Raider, again unless you chop.
RMR, just a generic RMR footprint that should fit the coming Glock Raider or 3rd party slides on a the RXM Raider, or whatever else comes in the future. Not for use on the 320, it’s too wide and will interfere with the Raider itself. I designed it to be compatible with or without Zev posts and the usual 82° torx screws.
Leave any questions or feedback below

SCOUT PRO MOUNT for Q’s QSERT mounting system
Reversible, run it up or down, left or right, put your light wherever you want on your Fix, Boombox or AR with their anticipated QSERT AR hand guard. Pairs well with SWITCH DOCK to run a Modbutton Lite.
Expect them to go live on the site in the next few weeks.

RMR footprint update.
Thanks to a generous follower I have a loaner Zev Octane slide to design around.
TLDR, P320 is getting its own RMR models and I’ve drawn up the four main versions, Tall/Tall Portal and Short/Short V for use with the Tactical Dev Halo. More details on the process below.
I was planning on having a generic RMR footprint that would be the width and profile of a Glock but fit anything else cut for RMR. But due to constraints of the Raider itself, any overhang on the P320 slide meant interference with the Raider’s rear optic mount.
When it comes to RMR, there is a ton of variance between slide manufactures and machine shops doing optic cuts, so I’m trying to make these fit as many of them as possible without compromise.
So having the Zev as the baseline these HELPeRs have the clearance for the Zev screw posts, but will work for cuts without. The recoil lug recesses are oversized at the moment to account for variances between brands and third-party cuts, testing more slides may allow tightening this up. Research has shown there is a lot of gray area here.
One major thing to note, if your slide has an “irons forward” optic cut, these will not be compatible with the Raider unless you do the “Chop” and remove the rear optic mount.
I’ll have an aluminum sample made once I work on another design for a slide coming this week.
If you have any RMR cut slide you’d like to send in to help move testing along, send a PM.

Early model for the coming RMR HELPeR. Mostly designed around matching Glocks with an RMR cut as far as aesthetics go since I expect that will be the primary user of this model, but realistically it should fit anything else cut for the RMR without issue. Once I have the opportunity to test fit, it will more forward and get an aluminum prototype for testing. Expect both a solid and portal versions later this year.
MOS should be next in the lineup. I have to get a slide to take measurements before I get started since @glockinc doesn’t want to share dimensions with me, then I can get things going as far as modeling and testing, expect these around the same time as RMR.









